• 01/15/01 03:02 PM
    Sign in to follow this  

    Fire Tutorial

    Graphics and GPU Programming

    Myopic Rhino
    Hopefully this information file will give you all the information you need to code your own fire routines, seen in many demos, and also to actually take it all further and develop your own effects..

    First thing we need to do is set up two arrays. The size of the arrays depends on the many things: screen mode, speed of computer etc. It's not really important, just that they should both be the same size... I'll use 320x200 (64000 byte) arrays for this text, because that happens to be the size needed for using a whole screen in VGA mode 13h.

    The next thing we need to do is set a gradient palette, this can be smoothly gradiated through ANY colours, but for the purpose of this text let's assume the maximum value is a white/yellow and the bottom value is black, and it grades through red in the middle.

    Ok, we have two arrays, lets call them startbuffer and screenbuffer, so we know whats going on. Firstly, we need to setup an initial value for the start buffer... so what we need is a random function, that returns a value between 0 and 199 (because our screen is 200 bytes wide) this will give us the initial values for our random "hotspots" so we do this as many times as we think is needed, and set all our bottom line values of the start buffer to the maximum colour value. (so we have the last 300 bytes of the start buffer set randomly with our maximum colour, usually if we use a full palette this would be 255 but it can be anything that is within our palette range.)

    Ok, that's set the bottom line up.. so now we need to add the effect, for this we need to copy the start buffer, modify it and save it to the screenbuffer, we do this by averaging the pixels (this is in effect what each byte in our array represents) surrounding our target. It helps to think of these operations in X,Y co-ordinates. Lets try a little diagram for a single pixel.....
    [font="Courier New"][color="#000080"][bquote]This[nbsp]is[nbsp]the[nbsp]startbuffer[nbsp][nbsp][nbsp][nbsp][nbsp][nbsp][nbsp][nbsp][nbsp][nbsp]This[nbsp]is[nbsp]our[nbsp]screenbuffer

    Here we're going to calculate the value for X,Y (notice I didn't start at 0,0 for calculating our new pixel values?? that's because we need to average the 8 surrounding pixels to get out new value.. and the pixels around the edges wouldn't have 8 pixels surrounding them), so what we need to do to get the value for X,Y is to average the values for all the surrounding pixels... that means adding 0,0 0,1 0,2 + 1,0 1,2 + 2,0 2,1 2,2 and then dividing the total by 8 (the number of pixels we've takes our averages from), but there's two problems still facing us..
    1. The fire stays on the bottom line....
    2. It's slow....
    3. The fire colours don't fade...
    Ok, so first thing, we need to get the fire moving! :) this is really VERY easy. All we need to do is to take our average values from the pixel value BELOW the pixel we are calculating for, this in effect, moves the lines of the new array up one pixel... so for example our old X,Y value we were calculating for was 1,1 so now we just calculate for 2,1 and put the calculated value in the pixel at 1,1 instead.. easy..

    The second problem can be approached in a few ways.. first and easiest is to actually calculate less pixels in our averaging.. so instead of the 8 surrounding pixels we calculate for example, 2 pixels, the one above and the one below our target pixel (and divide by 2 instead of 8) this saves a lot of time, another approach is to use a screen mode, where you can set 4 pixels at a time, or set up the screen so that you can use smaller arrays (jare's original used something like 80X50 mode) which in effect reduces to 1/4 the number of pixels needed to be calculated.

    The third problem is just a matter of decrementing the calculated value that we get after averaging by 1 (or whatever) and storing that value.

    Last but not least, we need to think about what else can be done... well, you can try setting a different palette, you can also try setting the pixel value we calculated from to another place, so say, instead of calculating from one pixel below our target pixel, you use one pixel below and 3 to the right of our target... FUN! :))

      Report Article
    Sign in to follow this  

    User Feedback

    Create an account or sign in to leave a review

    You need to be a member in order to leave a review

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now

    There are no reviews to display.